Leeson Electric Motors

The Only Complete online Electric Motor - Swimming Pool Pump site on the Internet
Toll Free 1-877-986-6867
Burton, Michigan USA 48529

Swimming/Pool Spa Pumps

Fasco Electric Motors
Fasco Blowers

These blowers are common to many woodstoves and fireplace blower inserts
Be sure to scroll down the entire page
These Fasco Electric blowers / fans are sold as complete assemblies
We do not sell any parts for these units
Note: Blowers have wire leads, no power cords, plugs or switches
 

Note Regarding Speed Controls:
With more and more people using wood burning stoves during heating of some issues surrounding the speed controls that vary the air output from centrifugal blowers.
On a single speed blower, a speed control wired in series with the hot line will allow the user to control the speed of the blower. Many speed controls will not
lower voltage below 60 and will not allow the wheel to slow to 0 RPM. Also, the combination of a blower and a speed control can often result in what is called
“harmonic noise” – strange vibrations and/or noises in the customer’s unit. Slightly increasing or decreasing the blower speed can sometimes eliminate this problem
– but it is often not 100% removable. Care should also be used in applying solid state speed control devices, as they are often installed in the common line, or in
a non-polarized plug setup. So even though the motor may not be turning because the speed control is turned too low for the motor to operate, electricity is still
connected to the speed control and a potential shock hazard exists. Finally, do not use light dimmer switches as speed controls for the centrifugal blower.
Controls should be approved for use with the motors found in these units.

KBWC Solid State Variable Speed Controls for Shaded Pole and Permanent Split Capacitor Motors

Click here for additional Fireplace Blowers

 

 

Click Image
Enlarge Picture

Catalog #

                  Description

Dimension Drawing

 

HB-RBM121
  • Whitfield Pellet Stove Blower 12126109
  • 1/35hp, 1.5 amps, 115 Volt
  • 3000 RPM
  • Rotation = CW
  • 6" leads with flat connector plug (2 wires)
  • Ship weight 8 pounds
    not recommended for speed control
    mfgr = Rotom
    7021-7786, 70217786
    702111470, 7021-11470
 drawing unavailable

Outside Flange Dimension = 4 3/8" x 4"
Bolt Hole-center to center = 3 3/4" x 3 3/8"
 

 $116.98

7021-11253
  • Country Flame blower
  • 1/50 hp
  • 3000 RPM
  • 1.1 amps, 115 volts, 60hz
  • 79 CFM
  • Discharge: 2.72” x 1.66”
    not recommended for speed control
    mfgr = Fasco
 drawing unavailable $84.82
7058-1732
  • Frymaster OEM Replacement
  • .80 amps, 115 Volts, 50/60 hz.
  • 3240 RPM
  • Ball Bearings
    not recommended for speed control
    806-4504 SP, 806-4504SP
    7002-0898, 7002-2656
    Kooltronics 807-1245
    Frymaster 106-2994, 826-1512
    For model FPH350CSD
 drawing unavailable

Cooling fan on drive end to reduce bearing temperatures

 $61.50

R7-RB445
  • Rotom Replacement Blower For Dayton
  • 1/6hp, 2.2 amps, 115 Volts
  • 3.3" Diameter Motor
  • 549 CFM
  • Ball Bearings
  • PSC Motor
  • ship weight 13 pounds
    not recommended for speed control
    Dayton Equivalent 4C445, 1TDT2, 4YJ32
    7090-2378
Click to enlarge		 $123.95
Fasco Blower 50745-D500 50745-D500
  • 3100RPM Shaded Pole Blower
  • .21 amps @ 115 Volts 60hz.
  • Name Plate CFM 15
  • Ship Weight 7 lbs.
    Dayton equivalent 2C782, 1TDN2
    7021-1998
    not recommended for speed control
        $69.95
Fasco Blower 50746-D500 50746-D500
  • 3100RPM Shaded Pole Blower
  • .72 amps @ 115 Volts 60hz.
  • Name Plate CFM 120
  • Ship Weight 10 lbs.
    not recommended for speed control
 $135.27
Fasco Blower 50747-D230 50747-D230
  • 3200RPM Shaded Pole Blower
  • .26 Amps @ 208-230 Volts 50/60hz
  • Name Plate CFM 60
  • Ship Weight 7 lbs.

    • not recommended for speed control
$71.27
Fasco Blower 50747-D401 50747-D401
  • 3200RPM Shaded Pole Blower
  • .49 amps @ 115 Volts 50/60hz.
  • Name Plate CFM 60
  • Ship Weight 7 lbs.
    Dayton 1C180, 4C440, 1TDN7, 7021-3466
    6FHX4
    7021-7841 (England Stove)
    7021-9258 (NESCO)
    7021-8768

    • not recommended for speed control
$90.16
Fasco Blower 50747-D500 50747-D500
  • 3100RPM Shaded Pole Blower
  • .52 amps @ 115 Volts 60hz.
  • Name Plate CFM 60
  • Ship Weight 7 lbs.
    7021-2373 (Birmingham Stove)
    7021-4735 (China Metal)

    • 7021-4155
    not recommended for speed control
$69.90
Fasco Blower 50747-D600 50747-D600
  • 3200RPM Shaded Pole Blower
  • .52 amps @ 115 Volts 60hz.
  • Name Plate CFM 60
  • Ship Weight 7 lbs.
    (no conduit box)

    • not recommended for speed control
$71.88
Fasco Blower 50748-D500 50748-D500
  • 2900RPM Shaded Pole Blower
  • .81 amps @ 115 Volts 60hz.
  • Name Plate CFM 65
  • Ship Weight 7 lbs.
    AO Smith BO1065

    • Dayton 4C443, 1TDP3, 7021-4931
    7021-5713
    not recommended for speed control
$73.28
Fasco Blower 50748-D700 50748-D700
  • 2900RPM Shaded Pole Blower
  • .74 amps @ 115 Volts 60hz.
  • Name Plate CFM 65
    no On/Off switch
  • Ship Weight 7 lbs.
    Heat-n-glo 7021-4814
    7021-6146, 7121-6146

    • not recommended for speed control
$81.24
Fasco Blower 50752-D230 50752-D230
  • 3100RPM Shaded Pole Blower
  • .67 Amps @ 208-230 Volts 50/60hz.
  • Name Plate CFM 135
  • Conduit Box
  • Ship Weight 10 lbs.
    Dayton Equivalent = 2C915
    • , 1TDP6
    7021-3483
    not recommended for speed control
$120.23
Fasco Blower 50752-D500 50752-D500
  • 3100RPM Shaded Pole Blower
  • 1.1 amps @ 115 Volts 60hz.
  • Name Plate CFM 135
  • Ship Weight 10 lbs.
    Dayton Equivalent = 2C610, 4C442, 1TDP5
    7021-3467, 7021-2001, 7021-6745
    70730488, 7073-0488
    Dundas Greenhouse Blower
    7021-7857 (coast to coast)
    7021-4799 (England Stove)

    • not recommended for speed control
$112.71
Fasco Blower 50755-D230 50755-D230
  • 1600RPM Shaded Pole Blower
  • .51 Amps @ 208-230 Volts 50/60hz.
  • Name Plate CFM 160
  • Ship Weight 10 lbs.
    Dayton Equivalent = 2C916
    • , 1TDR1
    7063-5181
    not recommended for speed control
$131.50
Fasco Blower 50755-D500 50755-D500
  • 1600RPM Shaded Pole Blower
  • 1.0 amps @ 115 Volts 60hz.
  • Name Plate CFM 160
  • Ship Weight 10 lbs.
    Dayton Equivalent = 1C982, 1TDP9
    7063-5313 (Arrow Heating)
    7063-8322 (Country Flame)
    7063-8285 (Earth Stove)
    7063-6692, 7073-0616 (Even Temp.)
    7063-9534 (Heat Tech)
    7063-3869 (Martin Industries)
    7063-5031 (Mt Vernon Fireplace)
    7063-9813 (NESCO)
    7063-9224 (Regency)
    7063-8259 (Trane)
    7063-8259, 7063-8571 (Travis)
    7073-1480, 7073-1480 (US Stove)
    7063-5921 (Waterford Stove)
    7063-8537, 7063-8873, 7073-0616
     

    • not recommended for speed control

 

 $99.90
Fasco Blower 50756-D230 50756-D230
  • 1500RPM Shaded Pole Blower
  • .65 Amps @ 230 Volts 50/60hz.
  • Name Plate CFM 320
  • Ship Weight 10 lbs.

    • not recommended for speed control
$202.87
Fasco Blower 50756-D500 50756-D500
  • 1500RPM Shaded Pole Blower
  • 1.3 amps @ 115 Volts 60hz.
  • Name Plate CFM 320
  • Ship Weight 10 lbs.
    Dayton Equivalent = 2C069
    • , 1TDR5
    7063-7444
    not recommended for speed control
$187.85
Fasco Blower 50757-D500 50757-D500
  • 1560RPM Shaded Pole Blower
  • .55 amps @ 115 Volts 60hz.
  • Name Plate CFM 105
  • Ship Weight 10 lbs.
  • Motor mounted inside blower housing
    7063-5366
    7063-8322 (Country Flame)

    • not recommended for speed control
$123.98
Fasco Blower 50769-D230 50769-D230
  • 1400/1200RPM Shaded Pole Blower
  • 1.9 Amps @ 208-230 Volts 50/60hz.
  • Name Plate CFM 480
  • Ship Weight 10 lbs.

    • Dayton 4C870, 1TDT3, 7008-6481
    not recommended for speed control
$236.70
Fasco Blower 50769-D500 50769-D500
  • 1400/1200RPM Shaded Pole Blower
  • 3.55 amps @ 115 Volts 60hz.
  • Name Plate CFM 480
  • Ship Weight 10 lbs.
    George Mayer 7008-6357
    Mt Vernon Fireplace 7008-6059
    7008-6319, 7108-6084, 7008-6084
    Dayton 4C444, 1TDR7, 7008-6162
    9C404

    • not recommended for speed control

 

 $217.91

A071
  • 2850 RPM
  • 0.7 amps @ 115 Volts 60hz.
  • Sleeve Bearings
  • Name Plate CFM 71
  • Includes Power Cord
  • Ship Weight 5 lbs.
    Reference: 7021-7371
    not recommended for speed control
 $82.99
A082
  • 2800 RPM
  • .95 amps @ 115 Volts
  • Name Plate CFM 75
  • Ship Weight 10 pounds
  • 30" Lead Wires
    AO Smith # 9469
    7021-9457, 7021-11027, 7021-8181
    7021-9667, 7021-7757
    • , 7058-0225
    7021-7372, 7121-7586, 7021-8030
    7002-1942, 7002-2411, 7021-10215
    7021-10216, 7021-10309, 7021-10327
    7021-10511, 7021-10725, 7021-11027
    7021-11358, 7021-7290, 7021-7856
    7021-7850, 7021-7908, 7021-8129
    7021-8215, 7021-8286, 7021-8855
    7021-9037, 7021-9038, 7021-9081
    7021-9527,7021-9778, 7058-0064
    7058-0225, 7021-8165, 7021-7586
    not recommended for speed control
$99.98

A120
  • 3000 RPM
  • 1.1 amps, 120 volts
  • 2-Speed
  • Ball Bearings
  • CW Rotation
  • ship weight 7 pounds
    Aladdin Steel/Hearth & Home models
    230-1460, 7002-2983

    • not recommended for speed control
drawing unavailable $108.53
Fasco Blower A125 A125
  • 3200RPM Shaded Pole Blower
  • 1.1 amps @ 115 Volts 60hz.
  • Name Plate CFM 125
  • Low Profile Blower
  • Ship Weight 10 lbs.

    • 7021-10749, 7021-10183, 7021-6791
    7021-6809, 7021-7809, 7021-6375
    not recommended for speed control
$144.76

A166
  • 3160 RPM Shaded Pole Blower
  • 1.50 amps @ 115 Volts 60hz.
  • 145 CFM
  • Sleeve Bearings
  • Ship Weight 8 pounds
    This is the original 4C446 for Dayton
    4C005, 4C446,1TDP7, 7021-3469

    • 7021-6741
    not recommended for speed control

inside dimension of outlet: 3 1/4" x 2 1/8" approx.		 $66.98

A167
  • 2900 RPM Shaded Pole Blower
  • 0.4 amps @ 115 Volts 60hz.
  • 30 CFM
  • Sleeve Bearings
  • Ship Weight 5 pounds
    reference: 7002-3388
    not recommended for speed control
 $69.94
A133
  • 3000RPM Shaded Pole Blower
  • 1.2 amps @ 115 Volts 60hz.
  • Power cord 24" with 2-prong plug
  • Heat N Glow 7002-1241
    7002-2944, 7102-2944, 7002-2311, 7002-2143
  • Ship Weight 10 lbs.

    • not recommended for speed control
drawing unavailable

Length: 12 7/8"
Height: 4 3/8"
Width: 4"
Flange Opening: 4 3/4" x 1"

 $104.78
Fasco Blower A212 A212
  • 3000RPM Shaded Pole Blower
  • 1.25 amps @ 115 Volts 60hz.
  • Name Plate CFM 212
  • Ship Weight 10 lbs.

    • 7021-10550, 7021-7624, 7021-7931
    7021-9025
    not recommended for speed control
$147.95

A455
  • 1500/1100 RPM; 2-Speed
  • 1.5 amps @ 115 Volts 60hz.
  • Name Plate CFM 455
  • Ship Weight 14 pounds
  • Sleeve Bearings
    AO Smith # 9478, JE2K017
    not recommend for speed control
 $185.14

A1000
  • 1100 RPM; 2-Speed
  • 2.9/1.4 Amps @ 115/230 Volts
  • Name Plate CFM 1000
  • Sleeve Bearings
    Reference 7151-2676
    Dimensional ship wgt 50 lbs
    not recommend for speed control
 $268.80

A1200
  • 1500 RPM; 2-Speed
  • 6.8/3.4 amps @ 115/230 Volts
  • Name Plate CFM 1200
  • Sleeve Bearings
  • Dimensional ship wgt 50 lbs.
    not recommended for speed control
 $316.90
B160
  • Low Profile Blower
  • 3000 RPM
  • 1.56 amps @ 115 Volts 60hz.
  • Name Plate CFM 150
  • Magnetic Strip on back of mount
  • Sleeve Bearings
  • Kit contains speed control/thermal switch
  • 2 prong plug
    Fits: Heat n Glo - GFK-160A
    Royal - GFK-160A
    Regency Wood Stove Insert
    Rotom R7-RB168
    Instructions
 $128.48
Fasco Blower B2305 B22505
  • Transflo Blower
  • 3200RPM Shaded Pole Blower
  • .55 amps @ 115 Volts 60hz.
  • Name Plate CFM 80
  • Ship Weight 8 lbs.

    • not recommended for speed control
$103.42
Fasco Blower B2307 B22507
  • Transflo Blower
  • 3100RPM Shaded Pole Blower
  • .85 amps @ 115 Volts 60hz.
  • Name Plate CFM 115
  • Ship Weight 8 lbs.

    • not recommended for speed control
$119.66

B22508
  • Transflo Blower
  • 1500RPM Shaded Pole Blower
  • .7 amps @ 115 Volts 60hz.
  • Name Plate CFM 105
  • Ship Weight 8 lbs.
    (Ref. 101584 fireplace blower)

    • not recommended for speed control
$129.85
Fasco Blower B22510 B22510
  • Transflo Blower
  • 3100RPM Shaded Pole Blower
  • 1.0 amps @ 115 Volts 50/60hz.
  • Name Plate CFM 153
  • Ship Weight 8 lbs.

    • not recommended for speed control
$143.61
Fasco Blower B22513 B22513
  • Transflo Blower
  • 2780RPM Shaded Pole Blower
  • 1.3 amps @ 115 Volts 60hz.
  • Name Plate CFM 215
  • Ship Weight 8 lbs.
    Replaces AO Smith J513

    • not recommended for speed control
$122.89
Fasco Blower B23617 B23617
  • Centrifugal Blower
  • 3100RPM Shaded Pole Blower
  • .9/.45 amps @ 115/230 Volts 60hz.
  • Name Plate CFM 70
  • Ship Weight 8 lbs.
    Cross Reference Information: Franklin 80270, 7021-10288
    4MH41

    • not recommended for speed control
$132.17
Fasco Blower B23618 B23618
  • Centrifugal Blower
  • 3100RPM Shaded Pole Blower
  • .9/.45 amps @ 115/208-230 Volts 60hz.
  • Name Plate CFM 70
  • Ship Weight 10 lbs.
    Cross Reference Information: 7021-8034
    Goodman 7021-9000
    Fedders 031-7059, 80270
    Franklin 7021-10289, 4MH42

    • not recommended for speed control
$151.80
Fasco Blower B24220 B24220
  • Centrifugal Blower
  • 2600RPM Shaded Pole Blower
  • 1.3 amps @ 115 Volts 60hz.
  • Name Plate CFM 135
  • Ship Weight 10 lbs.
    Dayton 4C006, 1TDR6, 7021-4933
    7021-8249 (Sherwood / Enviro)
    7021-8711, 7021-7301, 7021-7758
    7021-7788 (check holes)

    • 7021-8844, 7021-7462, 7021-7582
    7021-7938
    not recommended for speed control
$87.75

R7-RB3
  • Rotom Brand
  • CFM 75; 3.3" diameter motor
  • 1 Speed, 3220 RPM
  • 0.34 amps, 115 Volts
  • CW Rotation
  • Permanent Split capacitor
  • Open Drip Proof
  • Ball Bearings
    Universal # 383
 Drawing not available
Square flange: 2 7/8" x 2 7/8"
Bolt holes: 2.25" OC
Outlet hole: 2.25"		 $86.98
Fasco Blower B30 B30
  • Centrifugal Blower
  • 3200RPM Shaded Pole Blower
  • .59 amps @ 115 Volts 60hz.
  • Name Plate CFM 45
  • Ship Weight 8 lbs.
    Dayton 4C012, 1TDN5, 7021-3486
    7021-4604
    • , 7021-5599, 7021-5593
    7002-1668, 7021-7655
    not recommended for speed control

Unit no longer is no longer supplied with a screen, Fasco obsoleted it.

$89.66
Fasco Blower B45227 B45227
  • Centrifugal Blower
  • 1650RPM Shaded Pole Blower
  • 1.86 amps @ 115 Volts 60hz.
  • Name Plate CFM 265
  • Ship Weight 10 lbs.
    Dayton Equivalent = 4C447, 1TDR3
    7063-3277
    Replacement motor = D1161
    7063-4794 (Arrow Heating)
    7073-0107 (Earth Stove)
    7073-1449 (England)
    7063-4996 (National Steel)
    7063-4769 (National Stoveworks)
    7063-6345 (Nor Aire Mfg.)
    7063-6861 (Orville Products)
    7063-4777 (Peacock Stove)
    7063-4755 (Russo Woodstove)
    7063-4996 (Steelcrafters)
    7063-6861 (Orville Products)
    7063-7102 (US Stove)
    7063-7529 (Vestal Mfg)
    7063-4824, 7163-4824
    • , 7063-4343
    not recommended for speed control
$102.37
D1161
  • 1/15hp
  • 1480 RPM, 2-Speed
  • 2.9 amps, 115 volts
  • Shaft: 5/16" x 2"
  • Motor Diameter 3.3"
  • Rotation: CCW Shaft End

    • not recommended for speed control
Replacement Motor for B45227 Blower $107.94
Fasco Blower B45227-2 B45227-2
  • Centrifugal Blower
  • 1650RPM Shaded Pole Blower
  • .93 Amps @ 230 Volts 50/60hz.
  • Name Plate CFM 265
  • Ship Weight 10 lbs.
    Dayton Equivalent = 4C869
    • , 1TDR4
    7063-7019
    not recommended for speed control
$112.66
Fasco Blower B45230 B45230
  • Centrifugal Blower - 2 Speed
  • 1600/1400RPM Shaded Pole Blower
  • 1.2 Amps @ 208-230 Volts 50/60hz
  • Name Plate CFM 460
  • Ship Weight 10 lbs.
    7063-3515

    • not recommended for speed control
$159.71
 
Fasco Blower B45267
Motor View
B45267
  • Centrifugal Blower - 2 Speed
  • 1600/1400RPM Shaded Pole Blower
  • 2.9 amps @ 115 Volts 60hz.
  • Name Plate CFM 460
  • Ship Weight 14 lbs.
    Dayton Equivalent = 4C264, 4C448
    7063-5176
    Replacement motor = AO Smith #563, BO1460
    7063-6002 (Heatilator)
    7063-7942 (Heat-N-Glo)
    7063-6341 (England)
    George Mayer 7063-5329
    Mt Vernon Fireplace 7063-5602
    Nor-Aire Mfg 7063-6344, 7063-6345
    7063-6406 (Travis), 7063-8346 (Ruegg Fireplace)
    7063-7871 (US Stove)
    7063-5034, 7063-5093
    7063-5128 (use on High Speed)

    • not recommended for speed control

Flange outside dimensions 9.5" x 5"		 $135.46
563
  • 1/15hp
  • 1630 RPM, 2-Speed
  • 2.9 amps, 115 volts
  • Shaft: 5/16" x 2 1/2"
  • Motor Diameter 3.3"
  • Rotation: CW Lead End

    • not recommended for speed control
Replacement Motor for B45267 Blower
7063-3108, 7063-5176, 7063-6169, 7163-3108, 7163-5176 87934057, D1161, 8254110480, JA2R225		 $101.30
Fasco Blower B47120 B47120
  • Draft Inducer - 3 Speed
  • 1360/1100/830 RPM Shaded Pole Blower
     3-Speed
  • 1.95 amps @ 115 Volts 60hz.
  • Name Plate CFM 160/144/112
  • Ship Weight 10 lbs.
    7063-7662, 7063-5986, 7063-6207
    Appalachian Stove
    Dayton Equivalent = 4C754, 1TDR2
    7063-5673
    Heatilator 7063-6596
    7063-6568 (Hutch Mfg)
    7063-8057 (Martin Industries)
    7063-9465 (Pacific Energy)
    7063-5996 (Rockhill Metal)
    7063-5957 (US Stove)

    • 7063-6512
    not recommended for speed control
$109.49
Fasco Blower B68042 B68042
  • Centrifugal Blower
  • 1100RPM Shaded Pole Blower
  • 5.6 amps @ 115 Volts 60hz.
  • Name Plate CFM 815
  • Ship Weight 10 lbs.

    • not recommended for speed control
$240.62
 
Fasco Blower B75 B75
  • Centrifugal Blower
  • 3000RPM Shaded Pole Blower
  • .59 amps @ 115 Volts 60hz.
  • Name Plate CFM 75
  • Ship Weight 8 lbs.
    Dayton 4C004, 1TDP1, 7021-3484
    Franklin Cast Products
    7021-4772
    7021-4797
    7021-5757 (Welenco)
    7021-2367

    • not recommended for speed control
$68.92
 

( Fasco electric blower page )

1999-2013 All rights reserved Electric Motor Warehouse
Prices and data subject to change without notice
Electric Motor Warehouse is a registered trademark of Winans Inc.
“For specific trademark and copyright information regarding this site, contact my trademark and copyright attorney”
Trademarks & Logos are copyrighted property of their respective owners
We recommend that all electric motors be installed by a qualified licensed contractor.
Disconnect power before attempting to service any electrical apparatus 
  Home | Contact us | Security | Policies |  Privacy |Testimonials